[ Pobierz całość w formacie PDF ]
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.7 11/20/2002
Rear drive axle, removing and installing Page 9 of 15
42-99
Rear drive axle, servicing
Note:
Constant Velocity (CV) joints are packed with
grease G-6.
Outer Total grease Proportions:
joint dia. required
Joint Boot
89 mm 90 g (3.2 oz.) 40 g (1.4 50 g (1.8
(3.5 in.) oz) oz)
Inner
100 mm 80 g (2.8 oz.) 30 g (1.1 50 g (1.8
(3.9 in.) oz) oz)
Note:
Re-grease the joint, if necessary, when replacing
the CV joint boot.
1 -
Circlip
Always replace
Use VW161a circlip pliers to remove and
install Fig. 5
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.7 11/20/2002
Rear drive axle, removing and installing Page 10 of 15
42-100
2 -
Gasket
Always replace; remove protective backing
and stick onto joint
3 -
Inner CV joint
O.D.: 100 mm (3.9 in.)
Replace only as complete joint
Removing Fig. 3
Pressing on Fig. 4
Greasing Note, page 42-99
4 -
Dished washer
Installation position Fig. 7
5 -
Inner CV joint boot with cap
Examine for splits and signs of chafing
Use drift to remove
Coat sealing surface of CV joint with D-3
before attaching to CV joint
6 -
Axle shaft
Identical length on left and right-sides
7 -
Outer CV joint boot
Examine for splits and signs of chafing
Ventilate before tightening clamp Fig. 2
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.7 11/20/2002
Rear drive axle, removing and installing Page 11 of 15
42-101
8 -
Clamp
Always replace
Tightening Fig. 1
9 -
Dished washer
Larger diameter (concave side) contacts
thrust ring
Installation position Fig. 6
10 -
Spacer ring
Installation position Fig. 6
11 -
Circlip
Always replace
Insert into annular groove of shaft when
installing; not visible when joint installed
12 -
Outer CV joint
O.D.: 89 mm (3.5 in.)
Replace only complete joint
Removing Fig. 8
Installing: drive joint onto shaft using
plastic-headed hammer until circlip
engages in groove
Greasing Note, page 42-99
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.7 11/20/2002
Rear drive axle, removing and installing Page 12 of 15
42-102
Fig. 1 Tightening clamp
Fig. 2 Venting CV joint boot
Attaching the CV joint boot onto the outer body of the joint frequently
requires compressing or squeezing the boot. This produces a vacuum in
the joint boot, which may cause a crease to the inside when driving
(arrow).
For this reason, after installing the joint boot, vent it briefly by letting some
air in at the small diameter to balance the pressure and restore the correct
boot shape.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.7 11/20/2002
Rear drive axle, removing and installing Page 13 of 15
42-103
Fig. 3 Removing inner CV joint
Notes:
Use arbor to drive off boot first.
Support ball hub.
Fig. 4 Pressing on inner CV joint
Note:
Chamfer on the inner diameter of the ball hub (splines) must be facing
toward the shoulder of the drive axle.
- Press joint on up to stop.
- Install circlip.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.7 11/20/2002
Rear drive axle, removing and installing Page 14 of 15
42-104
Fig. 5 Removing and installing circlip
Fig. 6 Installation position of dished washer and spacer ring
1 - Dished washer
2 - Spacer ring (plastic)
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.7 11/20/2002
Rear drive axle, removing and installing Page 15 of 15
42-105
Fig. 7 Installing dished washer in correct position
Fig. 8 Pressing off outer CV joint
- Clamp drive axle in vise using protective jaws.
- Remove clamp and push back boot.
- Screw in 3207 pressure spindle with M14-thread end into joint until CV
joint is pressed off splined shaft.
http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU01.42.7 11/20/2002 [ Pobierz całość w formacie PDF ]